Practical guide · Beginner

Brewing Efficiency: Mash vs Brewhouse Efficiency

Understand your system’s efficiency: PPG, gravity points, mash and brewhouse efficiency, process losses and water planning.

Updated · 4 min read

What you will learn

  • Distinguish mash efficiency from brewhouse efficiency.
  • Explain brewhouse efficiency from measured OG, volume and fermentables.
  • Identify where gravity points and volume are lost in the process.
  • Rely on measured history rather than theoretical assumptions.

Why efficiency matters

Efficiency measures how much of the fermentables’ potential your system actually extracts. It links grain weight, PPG potential, measured OG and the volume you collect. An unknown efficiency makes recipes unpredictable: OG too low, lower ABV than planned, or a misjudged malt quantity.

Efficiency at a glance

Gravity points come from OG: 1.060 is 60 points. PPG (points per pound per US gallon) expresses a fermentable’s maximum potential: the points obtained by dissolving one pound in one US gallon. In metric, points = PPG × kg × 8.345 ÷ litres; for example, 37 PPG is about 309 points per kilogram in one litre. Actual points combine measured gravity and collected volume; theoretical points come from the grain bill.

In the homebrewing glossary: Original gravity.

Mash efficiency and brewhouse efficiency

Mash efficiency is the share of the potential found in the wort before the boil, after mashing and sparging. Brewhouse efficiency is the share found in the fermenter: it also counts kettle, trub and transfer losses, so it is always lower. For example, BeerSmith quotes about 80% mash efficiency for 72% brewhouse efficiency on a home system.

How to calculate brewhouse efficiency

The calculator uses the measured OG, the final volume and the fermentable lines with their PPG. Actual points come from OG and volume. Theoretical points add up, for each fermentable, its weight times its PPG times 8.345. Brewhouse efficiency is the ratio between the two.

Measure OG and volume cold, at the same time. Evaporation concentrates the wort without removing sugar: at the same temperature, points × volume stays roughly the same before and after. Cooling concentrates nothing: hot wort takes about 4 % more volume, but its temperature-corrected gravity is unchanged. A volume measured hot must therefore be brought back to cold, not combined with a cold OG. Wort left in the kettle, trub and transfers, on the other hand, carry sugar away and lower brewhouse efficiency.

Realistic efficiency ranges

Useful values depend heavily on the system and method. With no-sparge BIAB, brewhouse efficiency is often around 60 to 70% (Palmer uses 65% for no-sparge). A well-tuned three-vessel system often reaches 70 to 75% brewhouse efficiency; Palmer uses 75% for batch sparging and about 80% for fly sparging, measured before the boil. What matters is not the highest value but a stable, measured value you can reuse in recipes.

Where efficiency is lost

The crush strongly affects access to the sugars. The mash can lose efficiency if pH or temperature leaves the useful range. Lautering and sparging are often a major source of loss for homebrewers. After that, wort left in the kettle, trub and transfers lower brewhouse efficiency without changing mash efficiency.

Volumes and water plan

The efficiency calculator also covers process volumes: cold target volume, evaporation, trub losses, cooling shrinkage, mash water and sparge water. These volumes are not secondary. A good estimate of pre-boil volume and of the water plan makes the final OG more predictable.

A method for improving

Measure OG and final volume on every batch. Calculate and record your real efficiency. Change one variable at a time: crush, sparge, water ratio, pH or process losses. Measure again on the next batch. Once the value stabilizes, recalibrate your recipes on your real efficiency rather than an ideal one.

Common mistakes to avoid

The most common mistakes are using a theoretical efficiency you never checked, changing several parameters at once, confusing mash efficiency with brewhouse efficiency, measuring OG and volume at different temperatures, or forgetting volume losses. An efficiency figure is only useful if it is measured with a consistent method.

Sources

  1. How to Brew (online edition) — John J. Palmer, 2006
  2. Brewhouse Efficiency vs Mash Efficiency in All Grain Beer Brewing — Brad Smith, 2014
  3. Brewhouse Efficiency Calculator — Brewer's Friend
  4. Brew in a Bag Efficiency — Brew Your Own